Printing Materials - Versionsgeschichte

Friedrich am 9. Juli 2020 um 14:16 Uhr

2020-07-09T14:16:13Z

← Nächstältere Version		Version vom 9. Juli 2020, 16:16 Uhr
Zeile 1:		Zeile 1:
	== Filaments ==		== Filaments ==

	There exists a wide variety of filaments, but the most important ~~property~~ is the diameter.		There exists a wide variety of filaments, which all come with different properties, but the most important one is the diameter.
	~~Because~~ if you ~~have~~ the ~~wrong~~ diameter~~, then you can not print it~~.		So if you want to buy some printing material its important so look out for the right size.
	Also sometimes the tolerances on the diameter is not so tight in cheap filament, ~~wich~~ will lead to lower quality prints.		The Ultimaker 3 printer in the LAB uses 2.75mm Filament diameter.
	That is ~~simply~~ because the amount of material ~~applied is not constant if~~ the diameter of the filament changes every few meters.		Warning from personal experience: Don´t buy filament marketed as 3 mm because that is too thick for the Ultimaker and will get stuck.
	~~Ultimaker Printers utilize 2.75mm Filament whilest most other printers use 1.75mm.~~		Also sometimes the tolerances on the diameter is not so tight when buying cheap filament, this will lead to lower quality prints.
	~~Don´t buy filament marketed as 3 mm because that is too thick for~~ the ~~Ultimaker and~~ will ~~get stuck~~.		That is because the amount of material that the printer will extrude will relate to the diameter of the filament and if that changes every few meters the structure in your print will also be not uniform.
	<br>		<br>

	'''Materials:'''		'''Materials:'''
	*PLA		*PLA
			This can be considered as kind of standard 3d printing material.
			It is a plastic with a organic source which is easy to print.
	*PETG		*PETG

Friedrich am 23. Juni 2020 um 10:24 Uhr

2020-06-23T10:24:49Z

← Nächstältere Version		Version vom 23. Juni 2020, 12:24 Uhr
Zeile 6:		Zeile 6:
	That is simply because the amount of material applied is not constant if the diameter of the filament changes every few meters.		That is simply because the amount of material applied is not constant if the diameter of the filament changes every few meters.
	Ultimaker Printers utilize 2.75mm Filament whilest most other printers use 1.75mm.		Ultimaker Printers utilize 2.75mm Filament whilest most other printers use 1.75mm.
	Don´t buy filament marketed as 3 mm because that is to thick for the Ultimaker and will get stuck.		Don´t buy filament marketed as 3 mm because that is too thick for the Ultimaker and will get stuck.
	<br>		<br>

Friedrich: Die Seite wurde neu angelegt: „== Filaments == There exists a wide variety of filaments, but the most important property is the diameter. Because if you have the wrong diameter, then you ca…“

2020-06-23T10:24:25Z

Die Seite wurde neu angelegt: „== Filaments == There exists a wide variety of filaments, but the most important property is the diameter. Because if you have the wrong diameter, then you ca…“

Neue Seite

== Filaments ==

There exists a wide variety of filaments, but the most important property is the diameter.
Because if you have the wrong diameter, then you can not print it.
Also sometimes the tolerances on the diameter is not so tight in cheap filament, wich will lead to lower quality prints.
That is simply because the amount of material applied is not constant if the diameter of the filament changes every few meters.
Ultimaker Printers utilize 2.75mm Filament whilest most other printers use 1.75mm.
Don´t buy filament marketed as 3 mm because that is to thick for the Ultimaker and will get stuck.
<br>

'''Materials:'''
*PLA

*PETG

*ABS

*TPU

*OTHERS

<br>
[[3D printer@lab| Back to 3D Printer@ LAB]]